Swiss k11 serial number10/30/2022 ![]() ![]()
#SWISS K11 SERIAL NUMBER SERIAL NUMBERS#We also have a PDF document of M1 Garand Serial Numbers we will release in. It is a magazine fed, straight pull, bolt action rifle chambered in 7.5x55mm Swiss Gewehrpatrone 1911 (GP11). M1a1 Serial NumbersThis database contains the Swiss Schmidt-Rubin straight. The Karabiner Model 1911 (K11) is the shorter, lighter, carbine model of the Swiss 1911 rifle. #SWISS K11 SERIAL NUMBER SERIAL NUMBER#Includes leather sling and matching serial number model 1918 bayonet with scabbard and leather frog. Bluing on the base of the magazine is heavily worn. ![]() IT IS A WAFFENFABRIK BERN FACTORY MANUFACTURE THAT DATES TO 1917 FROM WHAT I CAN FIND. SWISS K11 WAFFENFABRIK BERN Description: THIS SWISS K11 IS SERIAL 69891 WITH A MATCHING BOLT. Trigger guard has been reblued and has minor edge wear. A2156 W+F Bern Swiss K11 - s/n 151xxx USD 445.00. Trigger plate has light edge wear on the forward end of the magazine well. Finish wear around the exposed area of the barrel. The pin for the stacking arm is missing but the stacking lug is still present. Front barrel band has light edge wear on the hinge, a scratch on the bottom of the left side, and very light edge wear on the bayonet lug. Small scratches in the metal surface. Bluing on the front and rear barrel bands have been reblued and are a dark black in color. Finish wear on the right side of the receiver, to the right of the vent hole. ![]() Heavy finish wear is found at the rear on the top and left sides. There is moderate edge wear around the loading slot and the top side lightening cuts, and patches of finish wear across the top side. On the top side of the handguard, there are a few nicks near the armory repair at the base of the handguard and pressure marks before the rear barrel band. On the right side of the handguard, there is a cluster of small gouges below and to the left of the rear sight and a round gouge at the wood line before the front barrel band. On the left side of the handguard, there is a small dent and a light pressure mark below and to the left of the rear sight. There is a small cluster of small gouges on the underside of the stock at the toe and a small gouge to the left of the trigger plate. A few gouges are seen around the finger groove and a couple of pressure marks within the finger groove. On the right side of the stock, there is a small mark at the butt and on the comb. There are a few superficial scratches in the finish near the butt. On the left side of the stock, there is a small dent behind the rear barrel band, a patch of handling wear within the finger groove on the left half. Small gouges in the furniture are present and there are a limited number of pressure marks. #SWISS K11 SERIAL NUMBER CRACK#A third crack is found on the right side of the stock behind the rear barrel band this crack has not been repaired. ![]() There are two armory repairs found in the furniture: the grip has an armory repair to the right of the tang and there is an armory repair at the base of the handguard, rear of the original factory reinforcement. Stock and handguard matching serial numbers. Swiss K11 carbine, produced in 1931, in good condition with 80% finish. The definitive work on this subject, and Schmidt-Rubin rifles in general, is Die Repetiergewehre der Schweiz, Die Systeme Vetterli und Schmidt-Rubin, by Reinhart, Sallaz, and am Rhyn (ISBN 3-7276-7102-5, copyright 1991 by Verlag Stocker-Schmid AG, Dietikon-Zuerich, Schweiz), from which the tables given here are adapted.W+F Bern Swiss K11 w/ Matching Bayonet - sn 198xx5 Swiss Schmidt-Rubin rifles do not have the date of manufacture stamped on any of the rifle parts, so determining when the rifle (and mismatched parts, if any) were manufactured must be determined from the serial numbers. Source: Manufacture Dates of Swiss Schmidt-Rubin Rifles Starting with K31 serial number 868,901, beech wood rather than walnut wood was used for making the stocks. (Recognisable by “+CM” markings instead of the usual “+CN” markings) This experiment proved unsuccessful. Stocks made from laminated plywood were tested, but rejected.ĭue to supply shortages, Chromium Molybdenum Steel was use in place of Chromium Nickel Steel on various parts. The magazine was made from hardened steel. The receiver was made from hardened steel. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |